Furnace starts, then shuts off
A clogged filter, a dirty flame sensor or a failing pressure switch is the usual cause. Our technicians test and fix it on the spot.
Furnace RepairArcadia is a compact west-side neighborhood of roughly 400 single-family homes, and most of them depend on one gas furnace and one thermostat to get through winter.

With about 400 houses south of Westwood, Arcadia is small enough that neighbors talk about which furnace gave out last January. Most homes here heat with gas forced air and cool with central air. That setup is simple and reliable, but it rests on a handful of parts: the igniter, flame sensor, inducer motor, blower and the thermostat on the wall.
Our technicians repair those parts and help Arcadia homeowners get more out of the system they already have. A smart thermostat set up correctly, a filter changed on schedule and a yearly visit cut down on surprise breakdowns. When something does break, usually on a cold weeknight, we explain the cause in plain language and give you the price before starting.
A single-family house with one furnace and one thermostat works best when the thermostat is placed well and talks properly to the equipment. Older mercury and dial thermostats drift out of calibration, and early digital models often lack the wiring that modern furnaces expect. A smart thermostat installation includes checking the common wire, the furnace staging and the AC settings, so the new control runs the system the way it was designed.
Furnaces in these homes generally sit in the basement and draw return air through a single filter slot. A filter left in too long chokes airflow, overheats the heat exchanger and trips the high-limit switch, which shows up as a furnace that starts, runs a few minutes and stops. It is one of the most common no-heat calls we see, and one of the easiest to prevent with a filter change every one to three months.

Kalamazoo winters bring long runs of cold weather, and natural gas from Consumers Energy is the main heating fuel for most homes in the area. Turning the thermostat down at night and while the house is empty trims how long the furnace runs. A smart thermostat handles that schedule on its own and can show how many hours the furnace ran each day. Setbacks of a few degrees are enough; very deep setbacks make the furnace work hard to recover on below-zero mornings.
Arcadia is a short drive west of our downtown Kalamazoo office. A person answers (269) 360-5258 at every hour, holidays included, and the next available technician comes out. For thermostat installs and maintenance visits we set a time that suits you. For a furnace that has stopped, we head out as soon as a technician can get there and give you the price before any repair.
Common calls
A clogged filter, a dirty flame sensor or a failing pressure switch is the usual cause. Our technicians test and fix it on the spot.
Furnace RepairMissing common wires and wrong settings are common after a self install. We rewire and configure it to match your furnace.
Smart Thermostat InstallationA maintenance plan covers a furnace visit in fall and an AC visit in spring, scheduled for you.
HVAC Maintenance PlanWorn motor bearings or a loose blower wheel make the noise. We repair or replace the motor before it quits.
Furnace RepairWe check refrigerant, clean the condenser and test the capacitor and contactor.
AC RepairFAQ
It depends on your furnace and AC. Single-stage systems work with nearly any smart thermostat, while two-stage furnaces, variable-speed blowers and heat pumps need a model that supports them. Our technicians check your wiring and equipment and recommend a thermostat that fits, then install and set it up.
Common furnace repairs in 49006 typically run between $167 and $594. Cleaning a flame sensor or replacing a filter-related limit switch sits near the bottom, while an inducer motor or control board sits higher. The technician quotes the exact repair after diagnosis, and you approve it before work begins.
Our plan covers a furnace tune-up in fall and an AC tune-up in spring, with cleaning, safety checks and measurements on each visit. We contact you when each visit is due, so it never slips. For a single-family Arcadia home with one system, the plan typically runs about $16 to $23 a month.
Call (269) 360-5258. Our Kalamazoo office answers 24/7 and books the next open technician.